Collar Science 
Tone & Spray 
Remote Trainer
 Quick Start Guide 

 What's inside the Case

Each Collar Science Bark Collar Includes: 

Protective carrying case

1 Spray traning collar 

Handheld remote trainer with lanyard

2 Removable, rechargeable lithium-ion batteries

2 Collar style options:

Adjustable silicone collar

Nylon collar

Micro USB charging cable

1 can of spray refill

Charge and Insert the Battery

2.1 Fully Charge The Battery

Before using your Training collar for the first time, charge the battery for 2 hours using the included charging cable.

A charging port is located on the side of the hard case for easy charging and storage.

2.2 Insert the Battery into the Back of the Collar

Insert the battery into the back of the spray collar and press down firmly until you feel a ā€œclick" This ensures itā€™s properly seated and ready for use.

Fill the Collar with Spray

3.1 Locate The Fill Port

Remove the pressure-fit silicone collar attachment from the spray tank arms.

The silicone strap may be snug - pull firmly to remove.

Locate the fill port on the pack left side of the collar's clear tank.

3.2 Positon The Tank

Twist the tank arms so that the fill port is facing upward and the opposite side of the tank is facing downward.

3.3 Insert the Refill Can

Place the refill can nozzle firmly into the fill port.

Firmly push the can down to depress the nozzle.

You should see the spray fluid begin filling inside the clear tank.

Release the downward pressure, then repeat.

For a quicker fill, press and release the nozzle several times until the tank is full. Donā€™t worry about overfilling, once the collar is full, any excess spray will safely dissipate.

Size and Attach the Silicone Collar

4.1 Attach the Silicone Collar to the Spray Unit

Press the pressure-fit silicone collar onto both ends of the spray tank.
Push firmly until seated; a tight fit and some resistance are normal.

4.2 Measure for the Correct Fit

āš ļø Make sure the unit is powered OFF before proceeding.

Place the collar around your dogs neck

Measure the silicone strap for their neck size

The collar sound fit snugly, with room for two to three fingers

Pull the three silicone tabs through the holes at your desired length

Stretch the silicone holes over the tabs to secure

4.3 Trim the Excess Collar 

āš ļø Remove the collar from your dog before cutting 

make sure you have chosen the correct length before proceeding

Measure and cut off the extra silicone strap

4.4 Check the Final Fit

Place the sized collar back on your dog

The collar should fit snuggly, with room for two to three fingers

Size and Attach the Nylon Collar 

(Optional Accessory)

5.1 Adjust the Tank Arms

āš ļø Make sure the unit is powered OFF before proceeding.

Twist both arms of the spray tank down until they form an upside-down ā€œUā€ shape.

Locate the 2 holes on the inside of the nylon collar.

5.2 Insert the Spray Unit into the Nylon Collar

Insert one tank arm into the first hole of the nylon collar.

Bend the other tank arm and insert it into the second hole, sliding it all the way in.

Adjust the nylon strap so it sits in front of the spray unit.

Rotate the tank arms back so they sit in their normal position and the collar forms a circle.

5.3 Adjust the Collar Size

Use the buckle on the nylon strap to adjust the length until it fits snugly around your dogā€™s neck.

5.4 Lock and Unlock the Collar Clasp

LOCK: push the clasp lock toward the opposite side of the clasp.

UNLOCK: push the clasp lock away from the opposite side.

5.5 Check the Final Fit

Place the collar on your dog.

It should be snug, but you should be able to fit 2ā€“3 fingers between the collar and your dogā€™s neck.

The nylon collar is now properly adjusted to your dog.

Adjust the Spray Angle

Collar Science adjusts to your dogā€™s unique face shape, from pug to beagle and beyond. The right spray angle ensures the most effective training.

āš ļø ALWAYS adjust the spray angle while the collar is powered OFF.

The correct position is for the spray to go directly in front of your dogā€™s nose.

The spray should not go under the chin or too far out in front of the face.

To adjust, twist the tank handles until the spray unit is aimed in the correct position.

This may take a few tries to get the angle just right for your dog.

Correct angle = most effective spray + best results.

Power ON and OFF

7.1 Power ON the collar

Press Power button Down for 2 Seconds than Release

Button will blink GREEN once

7.2 Power OFF the collar

Press Power button Down for 2 Seconds than Release

Button will blink RED 4 times

7.3 Power ON the Remote

Press the WHITE power button on the remote 1 second then release

The light will blink GREEN times and the remote will vibrate once.

the light will blink GREEN every 5 seconds to indicate the remote is still ON

7.3 Power OFF the Remote

Press the WHITE power button on the remote 3 second 

The light will blink GREEN 4 times and the remote will vibrate 4 times.

The remote is now OFF

Pairing the Remote and Training Collar

Each training collar comes paired with its remote.
In some cases, you may need to pair the remote again. If so, follow these steps:

1. Start with the collar OFF 

2. Turn ON the collar by pressing and releasing the button on the collar

3. Enter Feature Access mode on the remote:

Press and hold the Remoteā€™s power button until the light flashes alternating GREEN and RED (approximately 6 to 8 seconds).

This indicates the Remote is in Feature Access Mode, which allows pairing and advanced settings.

4. Begin pairing:

Hold the Remote close to the Collar.

Press and release the Remoteā€™s power button once.

The lights on both the Collar and Remote will flash GREEN three times and then RED, indicating they are ready to pair.

5. Complete the pairing:

Within 3 seconds, press and release the remoteā€™s power button a second time.

Both the remote and collar will flash GREEN three times and beep twice, confirming a successful pairing.

6. Exit feature access mode:

Wait approximately 30 seconds for the remote to automatically exit pairing mode; the RED and GREEN lights will stop blinking.

The remote and collar are now ON and ready to use.

āš ļø If paring was unsuccessful:

When you attempt to use the remote, the red light will flash three times.

This indicate the remote is not paired with the collar, and you will need to repeat the pairing steps.

7. After successful pairing.

The collar is now ready to use.

When the remote ins ON, its light will blink green every 8 seconds.

When the collar is ON, its light will also blink green every 8 seconds.

Adjust the Spray Volume

Our Bark Collar has 3 spray levels: Low, Medium, and High, designed to match your dogā€™s unique sensitivity.

Each collar starts on the Medium setting. 

Start at this setting to see how your dog responds.  

If your dog needs strong reinforcement switch to High 

If your dog is very sensitive switch to Low

šŸ’” Training Tip: Many dogs learn quickly with consistent use. Once your dog understands the correction, a lower spray setting often works just as well saving spray while keeping training effective.

Adjusting the Spray Volume:

1. Start with the collar OFF 

2. Turn ON the collar by pressing and releasing the button on the collar

3. Enter Feature Access mode on the remote:

Press and hold the Remoteā€™s power button until the light flashes alternating GREEN and RED (approximately 6 to 8 seconds).

This indicates the Remote is in Feature Access Mode, which allows pairing and advanced settings.

4. Select the spray level

      press the corresponding buttion on the remote:

LOW: Spray (no tone) button

MEDIUM: 1 spray + tone button

HIGH: 2 sprays (no tone) button

5. Confirm selection

Afer selection spray level, wait 10 seconds

The collar will beep twice and stop flashing RED and GREEN, indicating it has returned to normal user mode and is ready to use.